DCS WDU models Spécifications Page 126

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 318
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 125
UC864-E/G/WD/WDU AT Commands Reference Guide
80304ST10041a Rev. 7 - 2010-10-14
Reproduction forbidden without Telit Communications S.p.A’s. written authorization - All Rights Reserved. Page 126 of 318
+CGEQMIN – 3G Quality Of Service Profile (Minimum Acceptable)
OK
AT+CGEQMIN=?
+CGEQMIN: "IP",(0-4),(0-512),(0-16000),(0-512),(0-16000),(0-2),(0-
1520),("0E0","1E1","1E2","7E3","1E3","1E4","1E5","1E6"),("0E0","5E2","1E2","5
E3","4E3","1E3","1E4","1E5","1E6","6E8"),(0-3),(0,100-4000),(0-3)
+CGEQMIN: "PPP",(0-4),(0-512),(0-16000),(0-512),(0-16000),(0-2),(0-
1520),("0E0","1E1","1E2","7E3","1E3","1E4","1E5","1E6"),("0E0","5E2","1E2","5
E3","4E3","1E3","1E4","1E5","1E6","6E8"),(0-3),(0,100-4000),(0-3)
+CGEQMIN: "IPV6",(0-4),(0-512),(0-16000),(0-512),(0-16000),(0-2),(0-
1520),("0E0","1E1","1E2","7E3","1E3","1E4","1E5","1E6"),("0E0","5E2","1E2","5
E3","4E3","1E3","1E4","1E5","1E6","6E8"),(0-3),(0,100-4000),(0-3)
OK
Reference 3GPP TS 27.007; 3GPP TS 03.60/23.060/23.107; 3GPP TS 24.008
3.5.4.7.8. Quality Of Service Profile (Requested) - +CGQREQ
+CGQREQ - Quality Of Service Profile (Requested)
AT+CGQREQ=
[<cid>
[,<precedence>
[,<delay>
[,<reliability>
[,<peak>
[,<mean>]]]]]]
Set command allows to specify a Quality of Service Profile that is used when
the terminal sends an Activate PDP Context Request message to the
network. It specifies a profile for the context identified by the (local) context
identification parameter, <cid>.
Parameters:
<cid> - PDP context identification (see +CGDCONT command).
<precedence> - precedence class
<delay> - delay class
<reliability> - reliability class
<peak> - peak throughput class
<mean> - mean throughput class
If a value is omitted for a particular class then this class is not checked.
Note: a special form of the Set command, +CGQREQ=<cid> causes the
requested profile for context number <cid> to become undefined.
AT+CGQREQ? Read command returns the current settings for each defined context in the
format:
+CGQREQ: <cid>,<precedence>,<delay>,<reliability>,<peak>,
<mean>[<CR><LF>+CGQREQ: <cid>,<precedence>,
<delay>,<reliability>,<peak>,<mean>[…]]
If no PDP context has been defined, it has no effect and OK result code is
Vue de la page 125
1 2 ... 121 122 123 124 125 126 127 128 129 130 131 ... 317 318

Commentaires sur ces manuels

Pas de commentaire