DCS WD-30-BL Informations techniques Page 96
- Page / 310
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Advanced Configuration
Tsunami
®
8000 Series - Software Management Guide 96
After configuring the required parameters, click OK and then COMMIT.
Reboot the device, if you have changed any of the Wireless Interface parameters with an asterisk (*) symbol.
Given below are the default Antenna Gain, for devices with integrated antenna:
Wireless Inactivity
Timer
Resets the wireless interface if there is no change in the Tx and Rx Packet Count in the
specified interval of time. The default value is set to 5 seconds (disabled if set to 0
seconds) and can be configured between 5 to 600 seconds.
Legacy Mode By default, Legacy Mode is disabled. When enabled, the MP 8000 BSU and SU devices can
interoperate with the legacy products of the Tsunami
®
MP.11 family.
The MP 8000 devices that provide legacy support are,
• MP-8100-BSU
• MP-8100-SUA
• MP-8150-SUR
• MP-8150-CPE
• MP-8150-SUR-100
• MP-8200-BSU
• MP-8250-BS9
• MP-8250-BS1
• MP-8200-SUA
• MP-8250-SUR
: MP 8000 BSU device in legacy mode can connect to a MP 8000 SU device only
when configured in legacy mode.
Parameter Descriptions
Product (s) Antenna Gain
MP-8150-SUR 23 dBi
MP-8150-SUR-100 21 dBi
MP-8150-CPE 16 dBi
MP-8160-CPE 15 dBi
MP-8250-SUR 23 dBi
MP-8250-BS9 16 dBi
MP-8250-BS1 23 dBi
QB-8150-EPR 23 dBi
QB-8150-LNK-100 21 dBi
QB-8150-LNK-12/50 16 dBi
QB-8250-EPR 23 dBi
- 8000 Series 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- GPL License Note 2
- OpenSSL License Note 2
- Contents 3
- About this Guide 8
- Products Covered 8
- Audience 9
- Prerequisites 9
- Related Documents 9
- Documentation Conventions 9
- Overview 11
- 1.2 Wireless Network Topology 14
- 1.2.2 Point-to-Point Link 18
- 2.2 Command Line Interface 22
- 2.3 SNMP Management 23
- 2.4 ProximVision NMS 24
- Device Initialization 25
- 3.2.1 Home Page 29
- 3.2.2 COMMIT 30
- 3.2.3 REBOOT 31
- Basic Configuration 34
- 5.2 Network 44
- 5.2.2 Static Route Table 56
- 5.2.4 RIP 60
- 5.2.6 IP over IP Tunneling 67
- 5.3 Ethernet 71
- 5.3.2 Advanced Configuration 73
- 5.4 Wireless 74
- should be same 85
- Advanced Configuration 101
- 5.4.5 Roaming 104
- < (New BSU Rx SNR) then 110
- value ranging from0-10 110
- 5.4.6 BSU / SU Profiles 111
- 5.5 Security 114
- 5.5.2 RADIUS 117
- 5.5.3 MAC ACL 119
- 5.6 Quality of Service (QoS) 121
- 5.6.2 QoS Configuration 127
- Figure 5-64 QoS PIR Add Entry 132
- 5.8 VLAN (Bridge Mode Only) 151
- 5.10 Filtering (Bridge Only) 160
- 5.10.1 Protocol Filter 161
- Figure 5-94 Protocol Filter 162
- 5.10.3 Advanced Filtering 167
- 5.10.4 TCP/UDP Port Filter 169
- 5.10.5 Storm Threshold Filter 171
- 5.11 DHCP 177
- 5.11.2 DHCP Server 178
- 5.12 IGMP Snooping 182
- Management 184
- 6.1.2 Inventory Management 185
- 6.1.3 Licensed Features 186
- 6.2 File Management 187
- 6.2.3 Upgrade Firmware 190
- 6.2.4 Upgrade Configuration 192
- 6.2.5 Retrieve From Device 194
- 6.3 Services 198
- 6.3.2 Telnet/SSH 199
- 6.3.3 SNMP 201
- 6.3.4 Logs 204
- 6.5 Access Control 209
- 6.6 Reset to Factory 210
- 6.7 Convert QB to MP 210
- 7.1 Interface Statistics 212
- 7.1.2 Wireless Statistics 214
- 7.1.3 PPPoE Statistics 215
- 7.1.4 IP Tunnels 217
- 7.2 WORP Statistics 218
- 7.2.2 Link Statistics 222
- 7.3 Active VLAN 227
- 7.4 Bridge 228
- 7.4.2 Learn Table 229
- 7.5 Network Layer 230
- 7.5.3 ICMP Statistics 231
- 7.5.4 IP Address Table 232
- 7.5.5 DNS Addresses 232
- 7.5.6 Neighbour Table 233
- 7.5.7 RIP Database 233
- 7.7 IGMP 235
- 7.7.2 Router Port List 236
- 7.8 DHCP 237
- 7.9 Logs 237
- 7.9.2 Debug Log 238
- 7.9.3 Temperature Log 239
- 7.10 Tools 242
- 7.10.2 Scan Tool 243
- 7.10.3 sFlow® 243
- 7.10.4 Console Commands 247
- 7.10.5 Spectrum Analyzer 248
- Graph Results Interpretation 250
- 7.11 SNMP v3 Statistics 252
- Troubleshooting 253
- 8.1 PoE Injector 254
- 8.2 Connectivity Issues 255
- 8.6 Wireless Link Issues 259
- 8.9 Recovery Procedures 263
- 8.9.2 Bootloader Mode 265
- 8.9.3 Load a New Image 265
- 8.10 Spectrum Analyzer 269
- 8.11 Miscellaneous 269
- Feature Applicability 270
- Parameters Requiring Reboot 272
- BSU: Refers to a Base Station 275
- Introduction 276
- Point to Multipoint Devices 277
- Point to Point Devices 278
- 2.4 GHz Channels 279
- 4.9 and 5 GHz Channels 280
- ranging from 286
- LACP - Device Management 288
- Example2 289
- Bootloader CLI and ScanTool 292
- ScanTool 293
- SNR Information 294
- • MP-8150-CPE 296
- • QB-8150-LNK-12/50 296
- • MP-8200-BSU / SUA 299
- • MP-8250-BS9 / BS1 299
- • MP-8250-SUR 299
- Abbreviations 300
- Lightning Protection 304
- Statement of Warranty 305
- Other Information 306
- Support Options 307
- Telephone Support 308
- ServPak Support 308
- Packaged Services 308
- Technical Support Policy 309
Produits connexes et manuels pour Tiroirs chauffants DCS WD-30-BL
Tiroirs chauffants DCS WD-30-BL Spécifications
(238 pages)
(238 pages)
Tiroirs chauffants DCS WDU models Spécifications
(318 pages)
(318 pages)
Tiroirs chauffants DCS DCSWD27SSOD Manuel
(44 pages)
(44 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.317 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels