DCS RF15I Guide d'installation Page 16
- Page / 44
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
14
TROUBLE ShOOTiNG
PROBLEM POSSIBLE CAUSE CORRECTION
Ice cubes are too small
(less than 1/2 inch
thick).
1. Low ice consumption.
Ice is slowly melting in the ice bin and will affect the
size of the ice cubes. This is normal operation. When
the ice bin needs to be replenished, cubes will return to
regular size.
2. Not enough water in reser-
voir.
Make sure that the reservoir drain plug is installed
properly. Check the water line to the unit to make sure
there are no restrictions or kinks in the line. Check all
filters to make sure they are not restricted or plugged.
3. Distributor tube is
restricted.
See “CLEANING YOUR ICE MAKER” section for cleaning
the unit for proper operation.
4. Build-up of deposits on
evaporator plate.
See “CLEANING YOUR ICE MAKER” section for cleaning
the unit for proper operation.
5. Inadequate drain system.
Restriction in the drain lines will cause the ice in the bin
to melt to a thinner cube. If using a gravity drain, make
certain there are no kinks or restrictions in the drain
lines. If using a drain pump, check the inlet screen,
discharge line, and vent line for any build-up or restric-
tions.
6. Leaking drain valve.
See “CLEANING YOUR ICE MAKER” section for cleaning
the unit. This will also dissolve and flush out foreign
material in the drain valve causing it to leak.
7. Room temperature is too
warm.
Move to an area where temperature is below 90
degrees F.
Ice cubes are too big
(greater than 3/4 inch
thick).
1. Ice slab not releasing.
See “CLEANING YOUR ICE MAKER” section for cleaning
the unit for proper operation and cube size.
2. Condenser fan air flow is
restricted.
Make certain the grill in the front of the unit is free and
open for proper air circulation. Check and clean the
condenser coil by removing the grill in the front of the
unit. Clean the condenser with a vacuum and brush
attachment.
3. Room temperature is too
warm.
Move to an area where temperature is below 90
degrees F.
Hollow ice slab.
1. Distributor tube is
restricted.
See “CLEANING YOUR ICE MAKER” section for cleaning
the unit for proper operation.
2. Build-up of deposits on
evaporator plate.
See “CLEANING YOUR ICE MAKER” section for cleaning
the unit for proper operation.
3. Low water level in reservoir.
Make sure that the reservoir drain plug is installed
properly. Check the water line to the unit to make sure
there are no restrictions or kinks in the line. Check all
filters to make sure they are not restricted or plugged.
- ICE MAKER 1
- A MESSAGE TO OUR CUSTOMERS 3
- TABLE OF CONTENTS 4
- ELECTRiCAL 5
- STORiNG FOOD AND DRiNkS 5
- CLEANiNG 5
- DiSpOSAL 5
- UNpACkiNG yOUR iCE MAkER 6
- Built-In 55-80 degrees F 8
- Freestanding 55-90 degrees F 8
- DRAiN pLUMBiNG 9
- WATER SUppLy 9
- OpERATiON 10
- CARE AND MAiNTENANCE 11
- TROUBLE ShOOTiNG 15
- OBTAiNiNG SERviCE 19
- WARRANTy 20
- MAKER À GLAÇONS 23
- À L’iNTENTiON DE NOS CLiENTS 24
- TABLE DES MATiÈRES 25
- AvERTiSSEMENT 26
- RETiRER L’EMBALLAGE 27
- SpéCiFiCATiONS 27
- NOMENCLATURE 28
- FONCTiONNEMENT 31
- ENTRETiEN ET MAiNTENANCE 32
- DépANNAGE 36
- GARANTiE 41
- Customer Care: 888.936.7872 44
- Fax: 714.372.7003 44
Produits connexes et manuels pour Les fabricants de glaçons DCS RF15I
(36 pages)Airaid 300-159 manuels
Manuels d'utilisation et guides de l'utilisateur pour Équipement aérien Airaid 300-159.
Nous fournissons des manuels en pdf 1 Airaid 300-159 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels